| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129 |
- #
- # Makefile for "other" implemented platforms.
- #
- # * Copyright 2013-2015 by Bill Westfield. Part of Optiboot.
- # * This software is licensed under version 2 of the Gnu Public Licence.
- # * See optiboot.c for details.
- #
- #
- # Extra chips (maybe) supported by optiboot
- # Note that these are usually only minimally tested.
- #
- #
- # ATmega88
- #
- HELPTEXT += "target atmega88 - ATmega88 or ATmega88p (28pin, 8k)\n"
- atmega88: TARGET = atmega88
- atmega88: MCU_TARGET = atmega88
- atmega88: CFLAGS += $(COMMON_OPTIONS)
- atmega88: AVR_FREQ ?= 16000000L
- atmega88: $(PROGRAM)_atmega88.hex
- atmega88: $(PROGRAM)_atmega88.lst
- atmega88_isp: atmega88
- atmega88_isp: TARGET = atmega88
- atmega88_isp: MCU_TARGET = atmega88
- # 2.7V brownout
- atmega88_isp: HFUSE ?= DD
- # Low power xtal (16MHz) 16KCK/14CK+65ms
- atmega88_isp: LFUSE ?= FF
- # 512 byte boot
- atmega88_isp: EFUSE ?= 04
- atmega88_isp: isp
- atmega88p_isp: atmega88
- atmega88p_isp: TARGET = atmega88
- atmega88p_isp: MCU_TARGET = atmega88p
- # 2.7V brownout
- atmega88p_isp: HFUSE ?= DD
- # Low power xtal (16MHz) 16KCK/14CK+65ms
- atmega88p_isp: LFUSE ?= FF
- # 512 byte boot
- atmega88p_isp: EFUSE ?= 04
- atmega88p_isp: isp
- #
- # ATmega168p [QFN32]
- #
- HELPTEXT += "target atmega168p - ATmega168p\n"
- atmega168p: TARGET = atmega168p
- atmega168p: MCU_TARGET = atmega168p
- atmega168p: CFLAGS += $(COMMON_OPTIONS)
- atmega168p: AVR_FREQ ?= 16000000L
- atmega168p: $(PROGRAM)_atmega168p_16MHz.hex
- atmega168p: $(PROGRAM)_atmega168p_16MHz.lst
- atmega168p_isp: atmega168p
- atmega168p_isp: TARGET = atmega168p
- # 2.7V brownout
- atmega168p_isp: HFUSE ?= DD
- # Low power xtal (16MHz) 16KCK/14CK+65ms
- atmega168p_isp: LFUSE ?= FF
- # 512 byte boot
- atmega168p_isp: EFUSE ?= 04
- atmega168p_isp: isp
- HELPTEXT += "target atmega16 - ATmega16 (40pin, 16k)\n"
- atmega16: TARGET = atmega16
- atmega16: MCU_TARGET = atmega16
- atmega16: CFLAGS += $(COMMON_OPTIONS)
- atmega16: AVR_FREQ ?= 16000000L
- atmega16: $(PROGRAM)_atmega16.hex
- atmega16: $(PROGRAM)_atmega16.lst
- #
- # ATmega32
- #
- HELPTEXT += "target atmega32 - ATmega32 (40pin, 32k)\n"
- atmega32: TARGET = atmega32
- atmega32: MCU_TARGET = atmega32
- atmega32: CFLAGS += $(COMMON_OPTIONS)
- atmega32: AVR_FREQ ?= 11059200L
- atmega32: $(PROGRAM)_atmega32.hex
- atmega32: $(PROGRAM)_atmega32.lst
- atmega32_isp: atmega32
- atmega32_isp: TARGET = atmega32
- atmega32_isp: MCU_TARGET = atmega32
- # No OCD or JTAG, SPIEN, CKOPT (for full swing xtal), Bootsize=512B
- atmega32_isp: HFUSE ?= CE
- # 2.7V brownout, 16MHz Xtal, 16KCK/14CK+65ms
- atmega32_isp: LFUSE ?= BF
- atmega32_isp: isp
- #Atmega128RFA1
- HELPTEXT += "target atmega128rfa1 - ATmega128RFA1 (100pin, 128k)\n"
- atmega128rfa1: MCU_TARGET = atmega128rfa1
- atmega128rfa1: CFLAGS += $(COMMON_OPTIONS) -DBIGBOOT $(UART_CMD)
- atmega128rfa1: AVR_FREQ ?= 16000000L
- atmega128rfa1: $(PROGRAM)_atmega128rfa1.hex
- ifndef PRODUCTION
- atmega128rfa1: $(PROGRAM)_atmega128rfa1.lst
- endif
- # 1MHz clocked platforms/boards
- #
- # These are capable of 9600 baud
- #
- luminet: TARGET = $@
- luminet: CHIP = attiny84
- luminet:
- "$(MAKE)" $(CHIP) AVR_FREQ=1000000L LED_START_FLASHES=0 BAUD_RATE=9600
- mv $(PROGRAM)_$(CHIP).hex $(PROGRAM)_$(TARGET).hex
- mv $(PROGRAM)_$(CHIP).lst $(PROGRAM)_$(TARGET).lst
- luminet_isp: luminet
- luminet_isp: TARGET = luminet
- luminet_isp: MCU_TARGET = attiny84
- # Brownout disabled
- luminet_isp: HFUSE ?= DF
- # 1MHz internal oscillator, slowly rising power
- luminet_isp: LFUSE ?= 62
- # Self-programming enable
- luminet_isp: EFUSE ?= FE
- luminet_isp: isp
|
